Прошу подсказать что делаю не так. Изначально имею RB4011 как центральный роутер с несколькими CAP AC. На роутере настроен capsman с двумя сетями и виланами. Точки подключаются к контроллеру и работают прекрасно. Но, клиенты, которые подключаются непосредственно к роутеру (а он тоже имеет wifi и тоже управляется через capsman) не получают IP. Взял hAP AC с дефолтной конфигурацией, настроил по аналогии и получил ту же самую ошибку. Подскажите пожалуйста, что я не донастроил? Код: # model = RBD52G-5HacD2HnD /caps-man channel add band=2ghz-b/g/n frequency=2447 name=2.4 add band=5ghz-a/n/ac frequency=5180 name=5 /interface bridge add admin-mac=74:4D:28:E5:0B:FF auto-mac=no comment=defconf name=bridge add name=bridge26 /interface wireless # managed by CAPsMAN # channel: 2447/20-eC/gn(17dBm), SSID: 332123, local forwarding set [ find default-name=wlan1 ] band=2ghz-b/g/n channel-width=20/40mhz-XX \ disabled=no distance=indoors frequency=auto installation=indoor mode=\ ap-bridge ssid=MikroTik-E50C03 wireless-protocol=802.11 # managed by CAPsMAN set [ find default-name=wlan2 ] band=5ghz-a/n/ac channel-width=\ 20/40/80mhz-XXXX distance=indoors frequency=auto installation=indoor \ mode=ap-bridge ssid=MikroTik-E50C04 wireless-protocol=802.11 /caps-man datapath add bridge=bridge26 client-to-client-forwarding=yes local-forwarding=yes \ name=datapath26 vlan-id=26 vlan-mode=use-tag /caps-man security add authentication-types=wpa2-psk encryption=aes-ccm group-encryption=aes-ccm \ name=security26 passphrase=123456788 /caps-man configuration add channel=2.4 country=russia datapath=datapath26 datapath.vlan-id=26 \ datapath.vlan-mode=use-tag mode=ap name=2.4 rx-chains=0,1,2 security=\ security26 ssid=332123 tx-chains=0,1,2 add channel=2.4 country=russia datapath=datapath26 datapath.vlan-id=26 \ datapath.vlan-mode=use-tag installation=indoor mode=ap name=5 rx-chains=\ 0,1,2 security=security26 ssid=332123 tx-chains=0,1,2 /caps-man interface add configuration=2.4 configuration.mode=ap configuration.ssid=eer disabled=\ no mac-address=00:00:00:00:00:00 master-interface=none name=cap26 \ radio-mac=00:00:00:00:00:00 radio-name="" /interface list add comment=defconf name=WAN add comment=defconf name=LAN /interface wireless security-profiles set [ find default=yes ] supplicant-identity=MikroTik /ip pool add name=default-dhcp ranges=192.168.88.10-192.168.88.254 add name=pool26 ranges=192.168.26.10-192.168.26.50 /ip dhcp-server add address-pool=default-dhcp disabled=no interface=bridge name=defconf add address-pool=pool26 disabled=no interface=bridge26 name=dhcp26 /caps-man manager set enabled=yes /caps-man provisioning add action=create-dynamic-enabled master-configuration=2.4 name-format=\ prefix-identity name-prefix=2g add action=create-dynamic-enabled master-configuration=5 name-format=\ prefix-identity name-prefix=5g /interface bridge port add bridge=bridge comment=defconf interface=ether2 add bridge=bridge comment=defconf interface=ether3 add bridge=bridge comment=defconf interface=ether4 add bridge=bridge comment=defconf interface=ether5 add bridge=bridge comment=defconf interface=wlan1 add bridge=bridge comment=defconf interface=wlan2 /ip neighbor discovery-settings set discover-interface-list=LAN /interface list member add comment=defconf interface=bridge list=LAN add comment=defconf interface=ether1 list=WAN add interface=cap26 list=LAN /interface wireless cap # set bridge=bridge caps-man-addresses=127.0.0.1 enabled=yes interfaces=\ wlan1,wlan2 /ip address add address=192.168.88.1/24 comment=defconf interface=bridge network=\ 192.168.88.0 add address=192.168.26.1/24 interface=bridge26 network=192.168.26.0 /ip dhcp-client add comment=defconf disabled=no interface=ether1 /ip dhcp-server network add address=192.168.26.0/24 dns-server=192.168.88.1 gateway=\ 192.168.26.1 wins-server=192.168.88.1 add address=192.168.88.0/24 comment=defconf gateway=192.168.88.1 /ip dns set allow-remote-requests=yes /ip dns static add address=192.168.88.1 comment=defconf name=router.lan type=A /ip firewall filter add action=accept chain=input comment=\ "defconf: accept established,related,untracked" connection-state=\ established,related,untracked add action=drop chain=input comment="defconf: drop invalid" connection-state=\ invalid add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp add action=accept chain=input comment=\ "defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1 add action=drop chain=input comment="defconf: drop all not coming from LAN" \ in-interface-list=!LAN add action=accept chain=forward comment="defconf: accept in ipsec policy" \ ipsec-policy=in,ipsec add action=accept chain=forward comment="defconf: accept out ipsec policy" \ ipsec-policy=out,ipsec add action=fasttrack-connection chain=forward comment="defconf: fasttrack" \ connection-state=established,related add action=accept chain=forward comment=\ "defconf: accept established,related, untracked" connection-state=\ established,related,untracked add action=drop chain=forward comment="defconf: drop invalid" \ connection-state=invalid add action=drop chain=forward comment=\ "defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat \ connection-state=new in-interface-list=WAN /ip firewall nat add action=masquerade chain=srcnat comment="defconf: masquerade" \ ipsec-policy=out,none out-interface-list=WAN /tool mac-server set allowed-interface-list=LAN /tool mac-server mac-winbox set allowed-interface-list=LAN
